Views: 0 Author: Site Editor Publish Time: 2026-11-11 Origin: Site
Walk onto most shop floors and the MES terminal is the weakest piece of equipment in the cell. A 24-inch office monitor bolted to a shelf, a desktop PC under the bench collecting swarf, a keyboard nobody wants to touch with gloves on. It works for the pilot line and fails by month eighteen.
A panel PC replaces that stack with one sealed unit that drops into the cutout where the paper traveler used to hang. The Meetneng IPRO is one of the industrial panel PCs we build for the job. Seven sizes from 10.4 to 21.5 inches, a sealed aluminium body, two serial channels and two LAN ports.
Three failures repeat across plants. Dust and coolant mist enter the tower through its fan filter until the CPU throttles. Someone runs a VGA cable 15 meters along a cable tray and the image picks up noise from the drive. And the keyboard becomes a hygiene problem the moment the operator is wearing nitrile gloves and handling oily parts.
Office hardware is rated 0 to 40 °C and expects clean air. That is not a defect; it is a specification written for a desk, not a cell. The panel PC fixes the mechanical problem first: no enclosure, no shelf bracket, no cable run to a cabinet.
Four jobs, and each one sets a different hardware requirement.
Work order dispatch. The operator reads the order, the drawing revision and the quantity without walking to a printer. Character height at 1.5 m decides this, which is why brightness and contrast matter more than resolution.
Operation reporting. Scan the traveler or press a large on-screen button, enter good and scrap counts, confirm. Two taps, done with a glove on. If the button is 12 mm wide, the operator will use the keyboard instead, and the reporting discipline collapses.
Material traceability. A barcode scanner or RFID reader at the station, bound to a batch. This is the reason the terminal needs real serial ports, not a USB adapter that drops its COM number after a Windows update.
Equipment utilisation. Cycle times, stop reasons and run hours pulled from the machine and pushed to the MES. That traffic belongs on a second network interface, not on the same cable as the operator's screen updates.
If the terminal only has to do the first job, a cheap all-in-one survives. Once reporting and traceability are in scope, the port list and the touch type decide the project.
Size is set by viewing distance, the number of columns in your MES screen, and the cutout you already have.
A 10.4 or 12.1 inch unit suits a single-operation station, a small machine enclosure, or a fixture where the operator stands directly in front of it. Fifteen inch is the default for MES terminals: 4:3, 1024 × 768, enough for an order header, a component list and a keypad without scrolling. Step up to 17 or 19 inch when the screen has to be read from a step back or operated with thick gloves.
The 21.5 inch unit is a different animal. At 1920 × 1080 it belongs on a line dashboard or an andon board, showing output against target for the whole cell rather than one operator's order.
Aspect ratio matters as much as the diagonal. The 4:3 panels (10.4, 12.1 and 15 inch at 1024 × 768, 17 and 19 inch at 1280 × 1024) give more vertical rows, which is what an MES order list needs. The 15.6 and 21.5 inch units are 16:9 at 1920 × 1080, better for dashboards and side-by-side panels. If your MES was laid out for 1280 × 1024, a 4:3 screen avoids the horizontal scroll that makes operators miss fields.
Brightness is the one number that does not improve with size. The 10.4 and 12.1 inch panels are 500 cd/m², the 15 inch is 350, and everything from 15.6 inch up is 250. A 21.5 inch andon board facing a window will look washed out at 250 cd/m², so plan shading or specify a high-brightness panel.
Size | Resolution | Brightness | Outline (mm) | Weight |
10.4" | 1024 × 768 | 500 cd/m² | 277.3 × 224.5 × 55.8 | 2.75 kg |
12.1" | 1024 × 768 | 500 cd/m² | 311.3 × 255.3 × 55.6 | 3.3 kg |
15" | 1024 × 768 | 350 cd/m² | 367.3 × 291.3 × 58.8 | 3.75 kg |
17" | 1280 × 1024 | 250 cd/m² | 401.6 × 338.2 × 58.6 | 5.65 kg |
19" | 1280 × 1024 | 250 cd/m² | 445 × 374.8 × 58.6 | 5.7 kg |
15.6" | 1920 × 1080 | 250 cd/m² | 412 × 261 × 58.6 | 3.8 kg |
21.5" | 1920 × 1080 | 250 cd/m² | 551 × 340.2 × 53.5 | 6 kg |
Measure the existing cutout, not the old screen: the bezel covers a few millimetres each side, and a 2 mm error shows as a bright gap.
Capacitive glass is the standard build. It gives multi-touch, pinch and zoom, and a cleaner image because there is no extra layer over the panel. For an inspection bench, a clean room or a customer-facing kiosk there is nothing to discuss.
Resistive is a specified option, and it is only offered on the 10.4, 12.1, 15, 17 and 19 inch units; the 15.6 and 21.5 inch screens are capacitive only. Two details surprise buyers: on this range resistive costs more than capacitive, not less, and the film is rated at 100,000 cycles against five million.
Where it earns the money is the glove. Resistive responds to pressure, so nitrile, leather, a stylus or a wet hand all work. Capacitive needs a bare finger or a conductive glove. On a press line where nobody takes a glove off to press a button, that decides the project, and 100,000 cycles is the price of it. At 400 touches a shift, plan on replacing the film roughly once a year.
Two serial ports are standard, both RS232 with RS485 selectable, and a five-port RS232 expansion is available for cells that still run scales, gauges and older PLCs on separate drops.
Two LAN ports do more work than they look. One takes the machine network, the other the plant or MES network, which keeps a broadcast storm on the machine side away from the order system and gives the customer's security team a clean answer about segmentation. Four-LAN versions exist on the 7th and 8th generation boards, with a POE upgrade for cameras and a five-port variant.
Four USB ports cover the scanner, the RFID pad, a service keyboard and a USB stick for log export. HDMI and VGA run at the same time, so a second display above the station does not need an adapter. GPIO is optional, which is how most people drive a stack light without adding a PLC.
The housing is aluminium, and the back is one machined heat sink. Heat leaves through the body, so there is no intake filter to clean and no fan to seize, which removes the most common failure mode of a shop-floor computer.
The operating range is -10 to 60 °C. Storage is -20 to 70 °C on the 10.4, 12.1 and 15 inch units, and -20 to 60 °C on the larger ones, at 5 to 95 percent relative humidity without condensation. Those numbers assume air can move around the back of the unit. Bolt it into a sealed box with no clearance and you have built an oven, whatever the label says.
Power is 12 V DC, with a 9 to 36 V wide-voltage option for vehicles, forklifts and battery equipment. Worth specifying early if the terminal will ever leave the building.
A flat glass front with a sealed gasket is the difference between a two-minute wipe-down and a bag over the keyboard. In food, pharma and paint shops, that is often what gets the project approved.
Three ways, and the first is the one that sells the product.
Panel mount. The body has built-in hooks, so the unit clamps into a cutout from behind without drilling the bezel. This is the classic retrofit: the hole where the old pushbutton panel or the paper holder used to be becomes the terminal.
VESA arm. 75 × 75 and 100 × 100 patterns on the back let you hang the unit at eye level on a CR-05 or W01 cantilever, which is the right answer when two operators of different heights share a station.
Desktop. A stand for pilot lines and temporary cells, or a keyboard-tray base. The least protected position, so keep it away from coolant.
Depth runs 53.5 to 55.8 mm depending on size, and weight from 2.75 kg to 6 kg, so anything above 17 inch is a two-person lift into the cutout.
The chassis is the constant; the board inside it is not. The board sets three things that matter more than clock speed: how much memory fits, whether storage is mSATA or M.2, and which operating systems install.
Intel boards, Windows or Linux. The list runs from Celeron J1800 and J1900, the J1800 with one LAN port and the J1900 with two, through Core i3, i5 and i7. Third generation is the i5-3210M; fifth is the i3-5005U, i5-5350U and i7-5650U; sixth is the i5-6300U; seventh is the i3-7100U and i5-7300U; eighth is the i3-8130U, i5-8250U and i7-8550U; twelfth is the i5-1235U.
Two things change as you climb. Memory starts at one DDR3 slot capped at 8 GB on the J1800, J1900 and third generation boards, and becomes two slots and 16 GB from the fifth generation. The choices are 4 GB, 8 GB and 8 + 8 GB, so 16 GB is the ceiling. Storage is mSATA up to the fifth generation and M.2 from the sixth, which is the practical reason to start at sixth generation.
For an MES terminal, fifth or sixth generation is enough. Specify eighth or twelfth when the terminal also caches production data or runs a reporting client. A 5G module needs eighth generation or later.
Android boards, for display and input. Signage, andon boards, simple HMI and self-service terminals do not need a Windows licence. Six boards are offered, all with WiFi and Bluetooth on board. RK3288 runs 2 GB + 32 GB. RK3566 runs 2 GB + 32 GB, offers Linux Debian as well as Android, and accepts an HDMI input. RK3568D adds HarmonyOS and NeoKylin for domestic-OS projects. Allwinner H527 has eight cores and a 2 TOPS NPU. RK3576 and RK3588S carry 4 GB + 64 GB.
The standard Android configurations carry one LAN port. A dual-gigabit industrial board is available when an Android terminal has to bridge two networks.
The rule is blunt: if the terminal has to run an MES or ERP client, it is Intel and Windows. If it only has to display or take a simple input, Android costs less to own, with no licence and no antivirus.
Item | IPRO specification |
Touch panel | Capacitive standard; resistive option on 10.4″ to 19″ at extra cost. USB controller; ≥ 5 million touches (capacitive), ≥ 100,000 cycles (resistive) |
Processor | Intel Celeron J1800 (1 × LAN) / J1900 (2 × LAN); Core i5-3210M (3rd gen), i3-5005U / i5-5350U / i7-5650U (5th), i5-6300U (6th), i3-7100U / i5-7300U (7th), i3-8130U / i5-8250U / i7-8550U (8th), i5-1235U (12th). Android: RK3288, RK3566, RK3568D, Allwinner H527, RK3576, RK3588S |
Memory | DDR3 4 GB / 8 GB / 8 + 8 GB; one slot and 8 GB maximum on J1800 / J1900 / 3rd gen, two slots and 16 GB from 5th gen |
Storage | mSATA 128 / 256 / 512 GB up to 5th gen; M.2 128 / 256 / 512 GB from 6th gen; 1 TB SATA SSD; 1 TB or 2 TB mechanical hard disk optional |
LAN | 2 × LAN standard; 4 × LAN on 7th / 8th gen, with POE and 5-port options; 1 × LAN on standard Android builds |
Serial | 2 × RS232, RS485 selectable; 5 × RS232 optional |
USB | 4 × USB |
Display output | 1 × HDMI, 1 × VGA, simultaneous |
GPIO | Optional |
Wireless | WiFi + Bluetooth on Android boards; WiFi + BT or WiFi 6 module on Intel |
Operating system | Windows / Linux (Intel boards); Android 7.1 to 14, or Linux Debian (Android boards) |
Mounting | Embedded built-in hooks / VESA 75 × 75 and 100 × 100 / desktop, cantilever or keyboard-tray stand |
Operating temperature | -10 °C to 60 °C |
Storage temperature | -20 °C to 70 °C (10.4″, 12.1″, 15″); -20 °C to 60 °C (17″ and above) |
Humidity | 5% to 95% RH, no condensation |
Power | DC 12 V; 9–36 V wide voltage optional |
Options | 4G or 5G module, speaker, POE, 4 to 5 LAN |
Cutout tolerance. The clamps pull the bezel against the panel face, and the gasket needs even compression. A cutout 1 mm oversized in one corner shows as a shadow line on the glass.
Power. Budget a supply with headroom rather than matching the label; the inrush on a cold morning is higher than the running load. Earth the chassis at a dedicated point, not through the DC jack.
Recovery. Take an image of the configured terminal before it goes to the line. A panel PC that boots to a working MES client in four minutes is a spare part. One that needs a technician with a USB stick is a stoppage.
Will our MES client run on it?
It is a standard x86 platform running Windows or Linux, so an MES client or an OPC UA gateway installs normally. Send the software name and version and we will confirm the build.
We need more than two serial ports.
A five-port RS232 expansion is available on the same chassis, with RS485 selectable per port.
Can we get a sample before committing to a line rollout?
Yes. Send the cutout drawing, the software you intend to run and the environment, and our engineers will confirm the configuration before anything is cut.
The reason these projects go wrong is rarely the processor. It is a terminal that does not fit the hole, a touch layer that does not work with gloves, or a serial device that needs a port the unit does not have.
Start with the cutout, the glove and the peripheral list. Those three answers narrow seven sizes to one, and the IPRO datasheet has the outline and cutout drawings for each. If you are specifying a fleet, OEM and ODM panel PC customisation covers branding, default images and connector changes, all cheaper to settle before the first batch than after.