The 19-inch unit is the panel we quote when the machine door is already cut and the drawing says 429 mm. It is not a bigger version of a 15-inch HMI; it is the size at which the screen stops being an add-on to a button plate and becomes the operator station itself. 1280 × 1024 in 5:4 keeps the vertical axis that CNC and SCADA screens are laid out on, so a tool-path window, an axis readout and a program list can sit side by side without a second monitor.
Mechanically it is a 429.0 × 356.5 × 49.2 mm chassis with a 425.5 × 350.5 mm cutout, a flat louvered backplate and IP65 across the front face. The rear plate carries the display-side I/O — HDMI, VGA, four USB, one RJ45, audio and the DC terminal — while serial and additional network ports arrive on an expansion board. That split matters when the panel replaces an existing console: the cables that already exist at the door usually have to land in the same place.
| Availability: | |
|---|---|
OPC-19"
Meetneng
Machine builders do not start from the panel. They start from a cabinet drawing that already reserves a rectangle on the front door, and the panel either matches it or the door is re-machined. For that reason the numbers that close a 19-inch enquiry are 429.0 × 356.5 mm on the outside and 425.5 × 350.5 mm for the cutout — not the diagonal. We publish both, plus the 49.2 mm depth behind the door, because a deep console with a swing arm has less room behind it than the drawing suggests.
The 5:4 shape is the second half of that story. A 16:9 panel of similar width would be shorter, and every CNC or SCADA layout built for a square screen loses rows rather than columns — the alarm banner and the axis table are what disappear. Send us the cutout and the depth you have, and we will confirm whether the 19-inch fits before you commit to the door.
Nineteen inches at 1280 × 1024 gives 140 pixels per inch — low by consumer standards and exactly right for a control screen read at 600 to 900 mm. The interface stays at 100 % scaling with no fractional DPI, which is the single most common reason legacy HMI software looks broken on a modern monitor.
Brightness is quoted at 300 cd/m². That is deliberately higher than the 250 cd/m² of our 17-inch unit, because a 19-inch panel is more often used on an open machine frame under shop lighting than inside an enclosure. The front glass is anti-glare treated; it reduces reflection but does not make the panel sunlight-readable, and if the mounting point faces a window we will say so rather than quote a brightness figure the unit cannot hold.
The touch layer is projected capacitive with ten simultaneous points, specified for glove operation and water-drop rejection. In practice that means an operator who has just picked up a part does not have to take the glove off to acknowledge an alarm, and a splash on the face does not register as a press. The cover glass is tempered to ≥7H, so a swarf brush or a ring does not leave a permanent mark in the middle of the screen.
Two limits worth stating. Capacitive touch needs a bare or thin-gloved finger — heavy leather welding gauntlets will not register, and for those cells a resistive or non-touch build is the correct answer. And the front is IP65, not IP66/IP67: it survives washdown spray from the front, not immersion. Tell us the coolant pressure and the glove type on your line and we will confirm the configuration instead of leaving it to the datasheet.
Behind the screen sits a single-board x86 platform on a flat metal backplate with louvered airflow. The standard build runs a Celeron J1900 for terminal-style work — a screen, a keyboard wedge, a serial device and a network link. Core i3 and i5 builds cover vision inspection, in-line measurement and any cell where the panel also runs the motion supervisor. i7 to 12th generation is available for the small number of jobs that need it.
Memory tops out at 16 GB across the range, and storage is 128/256/512 GB on mSATA or M.2 NVMe with a 1 TB 2.5-inch SATA bay alongside. If your software vendor specifies 32 GB, this chassis is the wrong one and we would rather say that at quotation than at commissioning. Send us the CPU, RAM and storage you need and we will price the exact SKU rather than a range.
The rear plate is deliberately display-oriented: HDMI and VGA for a second screen, four USB for a scanner, a keyboard and a USB stick, one Intel Gigabit port for the plant network, mic and line out, and the DC terminal. On the standard unit that is the complete list. Serial ports and additional network ports are added on an expansion board, which is why the detail drawing labels them as expansion rather than as fitted.
This layout suits a panel that sits at the end of a cell and talks to a PLC over Ethernet. It does not suit a retrofit where four RS485 meters have to be polled directly — for that we configure the COM board before shipping. Tell us how many serial devices are on the machine and which protocol they speak, and the quotation will include the right board instead of an adapter you have to source locally.
Photographed rather than drawn: DC jack for 12 V with the 9–36 V terminal as an option, HDMI, VGA on a blue DB15, four USB-A in two stacked pairs, a single RJ45, a green mic jack and a pink line-out, and a metal power switch at the right-hand end. The two blank plates on the left are the expansion cutouts — that is where a COM board or a second network port appears when it is ordered.
We publish the photo because the drawing and the photograph disagree on one point in our own marketing set: the compute slide lists dual or quad Gigabit LAN, while the standard rear panel carries one port. Single LAN is what ships unless a second port is specified. Confirm the port count you need on the PO and there is no ambiguity later.
The front bezel is sealed to IP65 and the chassis is built for the vibration a machine tool puts through a door-mounted panel — the kind of load that loosens a consumer monitor bracket within a month. The operating range is −20 to 60 °C, quoted for continuous 7 × 24 duty rather than for a demo.
The honest caveats: IP65 applies to the front face only, the rear is a ventilated metal backplate and must stay inside a cabinet or a clean air path; and 60 °C assumes airflow behind the unit. A sealed cabinet that protects the PC also traps its heat, so a panel rated to 60 °C can still overheat in a closed box at 45 °C ambient. Tell us the ambient temperature at the mounting point and whether the door is ventilated.
Three mounting routes ship from the same chassis. Snap-in clips hold the panel in a 1.0–6.0 mm sheet-metal door with no front screws, which is what most machine builders use. A VESA 75 × 75 or 100 × 100 pattern on the backplate takes a cantilever arm when the operator needs the screen to swing to a second position. A desk stand covers commissioning benches and control rooms where the panel is not going into a door at all.
The clips are the part that decides installation time. They are rated for panel thickness down to 1.0 mm; a thinner door needs a backing plate, and a stainless door needs the cutout deburred before the gasket will seal. Tell us the door thickness and material and we will confirm the clip set that goes in the box.
The drawing carries the numbers an installer actually needs: 429.0 mm overall width, 356.5 mm height, 49.2 mm depth, a 425.5 × 350.5 mm cutout with a +0.5/0 tolerance, VESA 100 × 100 and 75 × 75 hole patterns on the backplate, and a panel thickness range of 1.0 to 6.0 mm for the snap-in clips.
A +0.5/0 cutout is a tolerance, not a target — cut to 425.5 and the gasket has material to seal against; cut to 426.5 and the panel drops through. Because the tolerance is one-sided, the cutout should be produced on a CNC or a laser, not by hand. Send the drawing back with your door dimensions marked and we will check the fit before the sheet metal is made.
In our order history the 19-inch panel lands in four places: CNC milling, turning and precision machining consoles; fiber laser cutting and welding control stations; robot cell control cabinets where one screen supervises several arms; and solar or lithium battery assembly lines where the panel is the station terminal. The common thread is a machine builder who needs one screen per cell, sealed, in a door, running their own software.
That is also why the ODM side matters more at this size than at 10 inches. Custom I/O, brightness, operating system image and front branding are all routine, and the front bezel can carry the builder's logo instead of ours. Tell us the application, the software stack and the annual volume, and we will quote both the standard SKU and the customised one so the comparison is on the table.
Item | Specification |
|---|---|
Model | 19-inch 5:4 industrial panel PC |
Display size | 19.0" TFT LCD, 5:4 aspect ratio |
Resolution | 1280 × 1024 (SXGA) |
Brightness | 300 cd/m² |
Touch type | 10-point projected capacitive (PCAP) |
Touch operation | Glove operation, water-drop rejection |
Cover glass | Tempered glass, ≥7H hardness, anti-glare treatment |
CPU options | Intel Celeron J1900; Core i3 / i5 / i7, 3rd to 12th generation |
Memory | 4 GB / 8 GB / 16 GB (16 GB maximum) |
Storage | 128 / 256 / 512 GB mSATA or M.2 NVMe SSD + 1 TB 2.5" SATA bay |
Graphics | Integrated Intel HD Graphics |
LAN | 1 × Intel Gigabit Ethernet (RJ45); dual or quad port via expansion board |
USB | 4 × USB-A on rear panel |
Serial | None on standard rear panel; RS232 / RS485 via optional COM board |
Display output | 1 × HDMI + 1 × VGA (dual independent display) |
Audio | 1 × mic in, 1 × line out |
Power input | DC 12 V standard; DC 9–36 V wide-range terminal optional |
Power consumption | Quoted against the selected CPU (on request) |
Operating temperature | −20 to 60 °C, with airflow behind the panel |
Cooling | Flat metal backplate with louvered airflow; fan spec confirmed per CPU |
Vibration / shock | Heavy vibration and shock resistance for machine-door mounting |
Ingress protection | IP65 front bezel; rear panel ventilated, not rated |
Mounting | Snap-in panel clips (1.0–6.0 mm panel); VESA 75 × 75 / 100 × 100; desk stand |
Outline dimensions | 429.0 × 356.5 × 49.2 mm |
Panel cutout | 425.5 × 350.5 mm, tolerance +0.5 / 0 |
Net weight | Confirmed per configuration (on request) |
Operating system | Windows 7 / 10 / 11, Windows IoT, Linux (drivers per SKU) |
Duty cycle | 7 × 24 h continuous |
Meetneng traces its manufacturing back to 2008, and designs and builds in Shunde, Foshan, Guangdong — the district that supplies much of China's appliance and electronics industry. The plant covers 5,000 m², and the work is not assembled from someone else's boxes: sheet-metal fabrication, board-level integration, system assembly, burn-in and software imaging all happen on the same site. That is why a change to a port layout, a housing or a nameplate can be answered with a date rather than an introduction to a third party.
The product range covers industrial panel PCs, fanless industrial PCs, embedded computers, rugged tablets, industrial displays and commercial self-service terminals — panel-mount, VESA, DIN-rail, desktop and floor-standing formats from one factory. Quality control runs to ISO 9001 with twelve inspection points from incoming components to the final functional test, and the field repair rate is held under 0.5 % — a number that matters more than any single specification on any one of those pages.
Thirty-plus patents are held by the engineering team, covering thermal design, structural details and the interface between the electronics and the enclosure. Units are issued with CE, FCC, LVD and RoHS documentation against the exact bill of materials of the build you order, because changing a radio module or a power supply changes the test scope.
More than 15,000 customers in over 100 countries have bought from us, across industrial automation, energy, medical equipment, security, retail and logistics. Reference accounts include Haier, Gree, BYD, Hikvision, Foxconn and CRRC. Most of those relationships began with a single unit on a single line, which is the pattern we plan for: the first sample has to be right, because the second conversation depends on it.
Trade happens in person as well as over email. We take our own stands at international industrial and electronics fairs — the collage below is our booths across several shows — and the engineers who answer an enquiry are often the ones standing there, so a specification question tends to get an answer on the spot rather than a promise to check. Between shows, buyers come to Shunde to walk the line, sign off a sample and agree packaging. Tell us when you are travelling and we will hold a slot and a sample build for the same week.
OEM and ODM are the default way we work rather than an exception. The engineering team takes a requirement list — CPU or SoC, memory, port count, enclosure, logo, packaging, software image — and returns a configuration and a lead time. The nameplate, boot logo, gift box and manual are the parts most buyers start with, and the SDK or driver documents are released to the account that orders the sample.
Units ship by express and air freight with export documentation and industrial protective packaging; stocked configurations leave within 72 hours and built-to-order units follow the lead time on the quotation. Tell us the application, the destination country and the annual volume, and we will come back with a configuration, a landed-cost estimate and a sample plan.
It is 5:4 — 1280 × 1024, the same family as our 15-inch 4:3 and 17-inch 5:4 units, not a 16:9 consumer panel. If your HMI layout was designed for a square screen, it will run unchanged. Tell us the resolution your software expects and we will confirm before you order.
The specified cutout is 425.5 × 350.5 mm with a +0.5/0 tolerance, so a 425 × 350 opening is 0.5 mm under size and will not take the panel without easing. Send us a photo of the opening with its measured size, and we will tell you whether a trim ring or a re-cut is the cheaper route.
None on the rear plate. The standard panel is display-oriented — HDMI, VGA, four USB, one RJ45, audio, DC. RS232/RS485 comes on an expansion board fitted before shipping. Tell us how many serial devices are on the machine and which protocol, and we will include the right board.
One Intel Gigabit port ships as standard. Dual or quad port is available through the expansion board. Our compute slide lists dual/quad options, and we flag that difference openly rather than let it surface at commissioning — tell us the port count you need and we will quote it in.
Yes, up to 12th gen i7 is offered, but the platform is priced per CPU and the thermal build changes with it. Give us the exact part number and the software it has to run, and we will quote the configuration that meets it rather than the top of the range.
No — 16 GB is the ceiling on this chassis, and that is a platform limit, not a pricing decision. If your application needs more, tell us what it is doing and we will point you to a box PC plus separate display instead of overselling this panel.
The backplate is louvered for airflow and the cooling arrangement is confirmed per CPU selection — the low-power builds do not need a fan, the i5/i7 builds are specified individually. Tell us the CPU you want and we will state the fan configuration in writing.
The front face is IP65 — it handles washdown spray from the front, and the touch layer rejects water drops so a splash does not register as a press. It is not rated for immersion, and the rear must stay inside the cabinet. Send us the spray pressure and angle and we will confirm.
Yes. Front branding, custom I/O, brightness and the operating system image are all routine ODM work at this size, and we quote standard and customised side by side. Send us the logo file, the OS image and the annual volume, and the quotation will cover both options.
Standard builds ship in the quantity-dependent lead time quoted on your PO, and the warranty term is stated on the quotation — do not assume three years from an older page. Tell us the quantity, the destination and whether you need CE or FCC documentation, and we will put all three on one quotation.